Great for: Standard hinged external TIMBER doors (painted or stained).
Not for: Aluminium frame doors, sliding doors/bifolds, or internal-only doors.
(For other door types, see our other kits.)
French doors | Cavity sliding doors | Internal doors

Why this kit

• Do two doors in one go (front + back)
• Seal the sides & top and the bottom
• Neat finish, durable, instant result
• Pre-mitred corners, so the results will look professional
• Aussie support if you get stuck
• Proudly Australian designed and manufactured

Great for: Standard hinged external TIMBER doors (painted or stained).
Not for: Aluminium frame doors, sliding doors/bifolds, or internal-only doors.
(For other door types, see our other kits.)
French doors | Cavity sliding doors | Internal doors

• Two sets of Perimeter seals (tops + sides) with pre-applied adhesive strip – discreet, low fuss and low-profile finish.  These are ecoMaster’s famous Draught Dodgers. 
• Bottom draught excluders (the standard model we fit on ~80% of doors) with fixings
• We email you full install videos (no printed guide — easier to watch than read)

What you’ll need (not included)

• Tape measure, pencil, square
• Fine-tooth saw (for trimming – straight cuts only – cornered mitre joined are pre-cut) 
• Drill/driver (for bottom excluder fixings)
• Cleaning wipes / methylated spirits (for surface prep)
• Scissors / utility knife, small step stool

Skill & time: Beginner-friendly | 60–90 mins per door

• Creates a continuous seal around the sides + top so wind can’t sneak in
• Adds a bottom sweep (our proven all-rounder) for a proper 360° seal
• Door still opens/closes smoothly

Long-lasting materials that won’t compress, crush, sag or fall off

How to Install your Front and Back Door Kit

Watcher: Seal your front & back timber doors step-by-step

1. Install the draught excluder (RP3)
2. Install the perimeter seal (Draught Dodgers)

Readers: Here are the installation instructions (but really, seriously, it’s much better if you watch the videos). 

Step 1: Gather Your Tools

• • Front and Back Door Draught Proofing Kit
  • Cleaning cloth 
  • Pair or scissors 
  • Tape measure
  • Pencil
  • Screwdriver (Philips head)
  • Hacksaw or drop saw (to trim to fit)
  • Drill

Step 2: Measure Your Door

Measure the width and height of your door and the available space on the frame to ensure your components will fit cleanly. Mark where each component will be installed, following the included video instructions.

Step 3: Fit the Raven RP3 Seal – Draught Excluder on the bottom of your door

• • Trim the Raven RP3 to the width of your door using a hacksaw or drop saw (better).
  • Attach it to the bottom of the inside face of your door as per the video instructions.
  • Adjust the screw mechanism so that the seal drops fully when the door closes, and lifts when it opens.

 Step 4: Install the Draught Dodgers

• • Use the included packer to position the timber mouldings at the correct distance from the door face.
  • Peel back the high-performance adhesive tape to fix the Draught Dodgers in place.
  • Install the compressive seal into the groove, then trim the ends neatly to suit. 

The result? A flexible perimeter seal that works even if your door has a wonky gap (which most do).

This creates a nearly invisible draught barrier that doesn’t drag or make your door harder to open.

The results you’ll feel

• No more icy hallway blasts
• Rooms hold heat longer
• Less street noise + dust
• Heating and cooling cycles less = lower bills

Which solution should go where?

Quick chooser

• Doing both front + back timber doors? → Front & Back Door Kit
• Just one external door, full seal? → External Door Kit
• Only sealing sides + top? → Draught Dodgers (1 or 2 door)
• Only sealing the bottom? → RP3 (hard floor) or RP35 (prams, walkers are used) , RP1 (over carpet)

FAQs (fast answers)

Will the door be harder to shut?
Set correctly, no. If your door is difficult to shut, more than likely the installation video was not watched and the packer was not used.  🙁 

Uneven threshold?
You might need to consult with our technical team – 1300 326 627 

Can I use this on aluminium doors?
No — this kit is for timber doors only.

Internal doors too?
This kit is for external timber doors. For internal draughts, see internal door kits.

What customers say

“Very impressed… works very well on my wonky door… bottom seals work great too on quite a large gap.”

“Despite having seals on our front door it still leaked… found Draught Dodgers and fixed it.  The front door is easier to unlock now too.”

“Thanks to the instructional YouTube video this was extremely straightforward… stopped the air roaring through all four gaps of my back door, and outside noise decreased too.”

“Fantastic for a variable large gap (up to 1 cm)… tried hardware-store products without success… Problem solved — no more cold air pouring in around the door!”

“Works beautifully on the front door that has huge gaps… Easy to install for the novice like me.”

“Put them on the front and back door. No more cold air blowing through my weatherboard house… easy to install… no more bending down to adjust door snakes.”

Need a hand?

Stuck mid-install? Our Aussie technical team can help you fast. 

Either call 1300 326 627 or jump onto chat at www.ecoMasterStore.com.au